Note:
1) If you need DC power supply for linear actuator, please click here to choose and buy.
2) If you need external limit switch for linear actuator, please click here to choose and buy.
3) If you need manual control switch for linear actuator, please click here to choose and buy.
Package Include:
1 x Electric Linear Actuator
1 x Receiver: S1PF-DC
1 x Transmitter: CP-3
2 x Mounting Brackets B
1 x User manual
The information for electric linear actuator:
Application:
Mainly used for doors, windows, cellars, trapdoors, hatchways, solar tracking system, medical devices, agricultural machinery, vehicles, ships, elevator platforms, lifting tables, TV lifts, robots, cabinetries, massage sofas, electric beds, medical chairs, and other electrical equipment. It can open, close, push, pull, lift, and descend these devices.
It can replace hydraulic and pneumatic products to save power consumption.
Feature:
High-quality products and high-quality services
High strength wear-resistant gear
Aluminum alloy telescopic tube and outer tube, good corrosion resistant
Heavy duty design, high-power DC motor
Strong thrust, up to 6000N / 600 Kgs / 1300 lbs
Multiple speed options, from 3.5 mm/second to 100 mm/second
Multiple stroke options, from 10 mm to 2000 mm
We can customize any stroke length from 10mm to 2000mm, such as 770mm, 1250mm, 1850mm and so on.
Advanced waterproof and dustproof technology
Low power consumption and low noise
Built-in two limit switches, linear actuator will automatically stop when stroke rod reaches the limit position.
Built-in limit switch signal output is optional.
Built-in Hall sensor is optional, so you can use the synchronous controller to operate 2, 3 or 4 linear actuators fully synchronously.
With auto-locking capability to hold load position after stopping, and no power supply is required.
Maintenance-free
Specifications:
Optional working voltage: DC 12V or DC 24V
Stroke range: 2 inches (50 mm)
Optional speed: 3.5±0.5mm/s, 5±1mm/s, 7±1.5mm/s, 9±2mm/s, 14±3mm/s, 18±4mm/s, 28±6mm/s, 38±8mm/s, 50±10mm/s, 100±20mm/s
The above is the speed at no load, and the actual working speed will gradually slow down as the load increases.
Max Load capacity: 6000N / 600 Kgs / 1300 lbs at 3.5mm/s
Linear actuator can get maximum load capacity when it operates in the vertical direction, and the pulling force is less than pushing force.
No-load current: 1~2A at 12V or 0.5~1A at 24V
Full load current: 6~12A at 12V or 3~6A at 24V
Please use a 12V/10A or 24V/5A power supply to power a linear actuator, or use a 12V/20A or 24V/10A power supply to power two linear actuators, or use a 12V/50A or 24V/25A power supply to power three or four linear actuators.
Shaft diameter: 24mm
The diameter of the mounting holes for the front and rear connectors:10mm [0.393in]
Housing Material: Aluminum Alloy
Stroke Rod Material: Aluminum Alloy
Gear Material: Polymer Plastic
Motor Type: Brushed DC Motor
The front connector style can be customized: the default is an open hole connector, which can be customized with slotted connector, internal thread connector, etc. And you can provide drawings for customization.
The orientation of the front and rear connector is default, we can rotate it 90 degrees during the production according to the customer's needs.
Duty Cycle: 10%, max 3mins continuous use
Service life: approx. 25,000 cycles
Power cable: two-core wire for normal linear actuators; six-core wire for linear actuators with built-in Hall sensors; four-core, five-core or six-core wire for linear actuators with built-in limit switch signal outputs.
Cable length of the normal linear actuator: 500±10%mm [20 in], the length can also be customized according to your specific needs.
Certifications: CE
Environment temperature: -26℃ to 85℃
Operating Noise: about 42dB~46dB (Linear actuators with different parameters will have different noise levels.)
IP rating: IP54, not suitable for outdoor use.
Wireless remote control Switch kit information:
Application:
This DC 12V 24V wireless remote control switch kit with radio receiver and RF transmitter.
It can long range remote control the extension and retraction of the electric linear actuator.
Feature:
Wireless control, easy to install.
Suitable for DC electric linear actuator.
Two operating voltage versions: DC 12V or 24V optional.
You can operate the linear actuator to extend or retract by using the buttons in the receiver or by the transmitter.
With limit terminals: You can connect sensors, limit switches or external devices to limit the stroke of the linear actuator.
With wired control terminals: You can connect manual switches to control the linear actuator.
You can use the transmitter / remote to control the receiver from any place within a reliable working distance.
The wireless RF signal from the transmitter can pass through walls, floors, doors or windows, but it will lose some operating range.
The receiver has reverse power protection and over current protection built in.
The receiver only works with the selected transmitter which is matched to the receiver.
One or more transmitters / remotes can control one or several receivers simultaneously.
Two or more receivers may be used in the same area.
Receiver Parameters:
Model: S1PF-DC12 / S1PF-DC24
Operating Voltage: 12±1VDC (model S1PF-DC12), or 24±2VDC (model S1PF-DC24), the operating voltage must be specified when ordering.
Output Voltage: 12VDC (model S1PF-DC12) or 24VDC (model S1PF-DC24)
2 control modes: Interlocking, Momentary
Quiescent Current: ≤10mA
Rated Current: 40A, so linear actuator maximum starting current cannot exceed 40A.
Wire range for the terminals: 22-12 AWG
Working Frequency: 433.92 MHz
Operating Temperature: -20°C ~ +70°C
Case size: 115mm x 95mm x 40mm (4.5 x 3.7 x 1.6 inches)
Transmitter Parameters:
Model No.: CP-3
Channel/Button: 3
Button Symbol:▲, ■, ▼
Operating Voltage: 12V (1 x 23A -12V battery)
Standby current: 4uA
Operating Current: 14mA
Operating Frequency: 433Mhz
Transmitting Distance: 500m / 1500ft (theoretically)
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 92mm x 40mm x 15mm
Applicable Transmitters:
This receiver can work with different transmitters. Such as model CP-3 (500 meters) and CB-3-2 (1000 meters).
Working Range:
With a transmitter (such as CP-3) to form a complete set, the maximum working distance can reach 500 meters in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.
If you want to have a further working range, you can install an external antenna to the receiver, and you also can use a high power transmitter, such as CB-3-2 transmitter.
Usage:
The receiver can be used to control DC 12V / 24V motor or linear actuator. If the power supply of those equipments is DC 12V, you should choose the receiver with same DC 12V version; and if the power supply of those equipments is DC 24V, you should choose the receiver with same DC 24V version.
Setting different control modes:
1) Setting Interlocking mode: Turn the mode switch in the receiver to "L".
The operation by the transmitter, such as CP-3:
Press button ▲ on the transmitter: The linear actuator extends outward.
Press button ■ on the transmitter: The linear actuator stops extending outward.
Press button ▼ on the transmitter: The linear actuator retracts inward.
Press button ■ on the transmitter: The linear actuator stops retracting inward.
2) Setting Momentary mode: Turn the mode switch in the receiver to "M".
The operation by the transmitter, such as CP-3:
Press and hold button ▲ on the transmitter: The linear actuator extends outward; Release button ▲: The linear actuator stops extending outward.
Press and hold button ▼ on the transmitter: The linear actuator retracts inward; Release button ▼: The linear actuator stops retracting inward.
Limit terminals:
The receiver has limit terminals, and you can connect external devices (with normally closed contact), such as sensors, limit switches to limit terminals, then use them to limit the stroke of the linear actuator.
For example, you can connect two normally closed limit switches to terminals “COM” and “UP”, and connect another normally closed limit switches to terminals “COM” and “DOWN”.
When the linear actuator extends outward, if discount two terminals “COM” and “UP”, the linear actuator automatically stop extending outward.
When the linear actuator retracts inward, if discount two terminals “COM” and “DOWN”, the linear actuator automatically stop retracting inward.
Wired control terminals:
The receiver has wired control terminals, and you can connect external devices (with normally open contact), such as manual switches to wired control terminals, then use them to control the linear actuator.
For example, you can connect three manual switches to wired control terminals “STOP”, “S1”, “COM” and “S2” according to following wiring diagram.
1) Control mode Interlocking:
When connect two terminals “S1” and “COM”, the linear actuator extends outward. And when connect two terminals “STOP” and “COM”, the linear actuator stops extending outward.
When connect two terminals “S2” and “COM”, the linear actuator retracts inward. And when connect two terminals “STOP” and “COM”, the linear actuator stops retracting inward.
2) Control mode Momentary:
When connect two terminals “S1” and “COM”, the linear actuator extends outward. And when disconnect two terminals “S1” and “COM”, the linear actuator stops extending outward.
When connect two terminals “S2” and “COM”, the linear actuator retracts inward. And when disconnect two terminals “S2” and “COM”, the linear actuator stops retracting inward.
Production time:
The linear actuators are the customized products, and these products are not in stock, we need to spend 3~7 working days to produce them according to the specified parameters in your order.
Return or Exchange:
The Linear Actuators are the customized products, we need to produce them according to the specified parameters in your order, so that we do not accept returns or cancel orders. If customers order unsuitable linear actuators themselves, we also do not accept exchanges, please understand.