This long range single-phase AC 110V 220V wireless remote control switch kit. The kit is one 8-button transmitter (such as transmitter CP-8 (1500ft), or CB-8 (3000ft)) control four 1 channel 30A relay output radio receivers. Each two buttons of the 8-button transmitter controls a receiver.
Package Include:
4 x Receiver: S1PU-AC-ANT3
1 x Transmitter: CP-8
1 x User manual
Application:
This long range single-phase AC 110V 220V wireless remote control switch kit with four 1-CH 30A relay output radio receivers and a 8-button transmitter.
It can long range control DC or AC equipments, such as lamp, LED lighting, motor, fan, solenoid valve, pump, electric lock, etc.
Feature:
Wireless control, easy to install.
Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.
Universal input: Support 110V AC (100V~120V) used in US, Canada, etc, and 220V AC (200V~240V) used in Germany, UK, France, etc.
Relay Output: This receiver is dry relay output, it can be used to operate both DC and AC equipment. The output terminals are NO / NC (normally open / normally closed), serving as a switch.
High Power: Each channel can work at maximum load current 30A.
With external antenna, the receiver has a farther working range.
The transmitter / remote can control the receiver from any place within a reliable working distance.
The wireless RF signal from the transmitter can pass through walls, floors, doors or windows, but it will lose some operating range.
The receiver has reverse power protection and over current protection built in.
The receiver only works with the selected transmitter which is matched to the receiver.
One or more transmitters / remotes can control one or several receivers simultaneously.
Two or more receivers may be used in the same area.
Receiver Parameters:
Model No.: S1PU-AC-ANT3
Operating Voltage: AC100~240V (110V/120V/220V/240V)
Output Type: Dry Relays Output (Normally Open and Normally Closed)
Maximum Load Voltage of Relay: 240VAC or 28VDC
Channel: 1 Way
3 Control Modes: Self-locking, Momentary, Interlocking
Quiescent Current: ≤6mA
Maximum Load Current of Relay: 30A
Wire Range of Terminals: 22-12 AWG
Working Frequency: 433MHz
Operating Temperature: -20°C ~ +70°C
PCB size: 90 x 59 x 18 mm
Case size: 138 x 68 x 50 mm
Transmitter Parameters:
Model No.: 0021014 (CP-8)
Channel/Button: 8
Button Symbol: 1, 2, 3, 4, 5, 6, 7, 8
Operating Voltage: 12V (1 x 23A -12V battery)
Operating Current: 8mA
Operating Frequency: 433MHz
Encoding Type: Fixed code by soldering, up to 6561 codes
Transmitting Distance: 500m / 1500ft (theoretically)
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 85 x 36 x 16 mm
Suitable Transmitters:
The receiver can work with 8-button transmitters. such as model CP-8 (500 meters) and CB -8 (1000 meters).
The receiver can also work with 2-button transmitters. such as model C-2 (100 meters), CP-2 (500 meters), CD-2 (Industrial, 1000 meters), and CB-2 (1000 meters).
Working Range:
With a transmitter (such as CP-8) to form a complete set, the maximum working distance can reach 500 Meters in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.
If you want to have a longer working range, you can replace the external antenna of the receiver,or use a high-power transmitter, such as a CB-8 transmitter.
Usage:
The receiver can be used to control both DC 0~28V and AC 110~240V equipments.
Notice: The receiver is dry relay output, not DC/AC power output. Initial state of relay output terminals: Terminals B and C are Normally Open; Terminals A and C are Normally Closed.
Wiring:
1) If you want to control a DC 12V lamp, do as following:
1-1) Connect the positive pole of DC power supply to terminal B of the receiver.
1-2) Connect the negative pole of DC power supply to the negative pole of DC lamp.
1-3) Connect the positive pole of DC lamp to terminal C of the receiver.
1-4) Connect the live wire of AC power supply to terminal “L / +” of the receiver.
1-5) Connect the neutral wire of AC power supply to terminal “N / −” of the receiver.
2) If you want to control an AC 220V lamp, do as following:
2-1) Connect the live wire of AC power supply to terminal B of the receiver.
2-2) Connect the neutral wire of AC power supply to one end of the AC lamp.
2-3) Connect the other end of the AC lamp to terminal C of the receiver.
2-4) Connect the live wire of AC power supply to terminal “L / +” of the receiver.
2-5) Connect the neutral wire of AC power supply to terminal “N / −” of the receiver.
Setting different control modes:
The buttons 1 and 2 of the 8-button transmitter controls the receiver 1.
The buttons 3 and 4 of the 8-button transmitter controls the receiver 2.
The buttons 5 and 6 of the 8-button transmitter controls the receiver 3.
The buttons 7 and 8 of the 8-button transmitter controls the receiver 4.
1) Setting Momentary mode: Press the learning button in the receiver 2 times, signal LED continuously flashes 2 times and then goes off.
The operation of Momentary mode with the transmitter CP-8:
Press and hold the button 1 on the transmitter: The relay in the receiver 1 is activated, and the connected lamp is turned on.
Release the button 1 on the transmitter: The relay in the receiver 1 is deactivated, and the connected lamp is turned off.
Press and hold the button 3 on the transmitter: The relay in the receiver 2 is activated, and the connected lamp is turned on.
Release the button 3 on the transmitter: The relay in the receiver 2 is deactivated, and the connected lamp is turned off.
Press and hold the button 5 on the transmitter: The relay in the receiver 3 is activated, and the connected lamp is turned on.
Release the button 5 on the transmitter: The relay in the receiver 3 is deactivated, and the connected lamp is turned off.
Press and hold the button 7 on the transmitter: The relay in the receiver 4 is activated, and the connected lamp is turned on.
Release the button 7 on the transmitter: The relay in the receiver 4 is deactivated, and the connected lamp is turned off.
2) Setting Self-locking mode: Press the learning button in the receiver 3 times, signal LED continuously flashes 3 times and then goes off.
The operation of Self-locking mode with the transmitter CP-8:
Press the button 1 on the transmitter: The relay in the receiver 1 is activated, and the connected lamp is turned on.
Press the button 1 on the transmitter again: The relay in the receiver 1 is deactivated, and the connected lamp is turned off.
Press the button 3 on the transmitter: The relay in the receiver 2 is activated, and the connected lamp is turned on.
Press the button 3 on the transmitter again: The relay in the receiver 2 is deactivated, and the connected lamp is turned off.
Press the button 5 on the transmitter: The relay in the receiver 3 is activated, and the connected lamp is turned on.
Press the button 5 on the transmitter again: The relay in the receiver 3 is deactivated, and the connected lamp is turned off.
Press the button 7 on the transmitter: The relay in the receiver 4 is activated, and the connected lamp is turned on.
Press the button 7 on the transmitter again: The relay in the receiver 4 is deactivated, and the connected lamp is turned off.
3) Setting Interlocking mode: Press the learning button in the receiver 4 times, signal LED continuously flashes 4 times and then goes off.
The operation of Interlocking mode with the transmitter CP-8:
Press the button 1 on the transmitter: The relay in the receiver 1 is activated, and the connected lamp is turned on.
Press the button 2 on the transmitter: The relay in the receiver 1 is deactivated, and the connected lamp is turned off.
Press the button 3 on the transmitter: The relay in the receiver 2 is activated, and the connected lamp is turned on.
Press the button 4 on the transmitter: The relay in the receiver 2 is deactivated, and the connected lamp is turned off.
Press the button 5 on the transmitter: The relay in the receiver 3 is activated, and the connected lamp is turned on.
Press the button 6 on the transmitter: The relay in the receiver 3 is deactivated, and the connected lamp is turned off.
Press the button 7 on the transmitter: The relay in the receiver 4 is activated, and the connected lamp is turned on.
Press the button 8 on the transmitter: The relay in the receiver 4 is deactivated, and the connected lamp is turned off.
How to pair the transmitter to the receiver:
Pair receiver 1:
1) Press the learning button once in the receiver 1, signal LED on the receiver 1 flashes one time and then stays on, this indicates that the receiver 1 enters the learning status.
2) Press button 1 on transmitter, if the signal LED flashes one time, this indicates that the pairing with button 1 is successful.
Then press button 2 on transmitter, if the signal LED flashes one time, this indicates that the pairing with button 2 is successful.
3) Press the learning button in the receiver 1 again for 1-2 seconds, signal LED turns off, this indicates that the receiver 1 exits the learning status.
Pair receiver 2:
1) Press the learning button once in the receiver 2, signal LED on the receiver 2 flashes one time and then stays on, this indicates that the receiver 2 enters the learning status.
2) Press button 3 on transmitter, if the signal LED flashes one time, this indicates that the pairing with button 3 is successful.
Then press button 4 on transmitter, if the signal LED flashes one time, this indicates that the pairing with button 4 is successful.
3) Press the learning button in the receiver 2 again for 1-2 seconds, signal LED turns off, this indicates that the receiver 2 exits the learning status.
Pair receiver 3:
1) Press the learning button once in the receiver 3, signal LED on the receiver 3 flashes one time and then stays on, this indicates that the receiver 3 enters the learning status.
2) Press button 5 on transmitter, if the signal LED flashes one time, this indicates that the pairing with button 5 is successful.
Then press button 6 on transmitter, if the signal LED flashes one time, this indicates that the pairing with button 6 is successful.
3) Press the learning button in the receiver 3 again for 1-2 seconds, signal LED turns off, this indicates that the receiver 3 exits the learning status.
Pair receiver 4:
1) Press the learning button once in the receiver 4, signal LED on the receiver 4 flashes one time and then stays on, this indicates that the receiver 4 enters the learning status.
2) Press button 7 on transmitter, if the signal LED flashes one time, this indicates that the pairing with button 7 is successful.
Then press button 8 on transmitter, if the signal LED flashes one time, this indicates that the pairing with button 8 is successful.
3) Press the learning button in the receiver 4 again for 1-2 seconds, signal LED turns off, this indicates that the receiver 4 exits the learning status.
How to delete all transmitters codes stored in the receiver:
Press the learning button in the receiver 10 times and then release the learning button, signal LED flashes 10 times quickly and then goes off, this indicates that all stored codes have been deleted successfully.